Tricks-Collections.Com

To clear the message from the LCD display on Sharp JX9400/9600 and TI Pro 600 printers:

1. Turn Printer off.
2. While holding down Enter and Menu keys, power the printer on.
3. You should see PCU Diag Mode displayed.
4. Hit Menu key 6 times till Counter Set is displayed.
5. Hit Enter key
6. Dev xxxxx displayed, left 3 numbers are blinking.
7. Hit (down triangle symbol) till numbers are 000.
8. Hit Menu key, right 2 numbers are blinking.
9. Hit (down triangle symbol) till numbers are 00.
10. Hit Menu key.
11. Drm xxxxx displayed, left 3 numbers are blinking
12. Repeat steps 7-10.
13. Dev tm xxxxx displayed.
14. Repeat steps 7-10.
15. Drm xxxxx displayed.
16. Repeat steps 7-10.
17. Life xxx displayed.
18. Life should be set to 005.
19. Hit Menu key.
20. TNL xxx displayed.
21. TNL level should be between 90-110, if you have problems, try changing TNL.
22. Hit Enter key
23. Counter Set is displayed.
24. Hold down Form Feed key and insert blank paper into manual feed slot.
25. You should get a beep confirming reset.
26. Power printer down and back up, you are done.

• 0 Comments

Maintenance Message Reset Methods for Lexmark Optra C710, 720, 750 printers
Optra C710

1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
2. Press the MENU button right or left until RESET FUSER COUNT appears
3. Press the SELECT button to reset the count

Optra C720

1. Enter the Diagnostic Menu for all resets by pressing the GO and RETURN buttons and turn the printer on
2. Continue holding until PERFORMING SELF TEST is displayed
3. Select RESET COUNTERS from the Diagnostic Menu
4. Select the individual counter for reset and press the SELECT button

Optra C750

1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test, the display will read CONFIG MENU
2. Select individual reset for fuser or ITU kit

• 0 Comments

Dibawah ini tempat download themes windows xp dan yang pasti bisa di download gratis

• http://www.dowtheme.com/
• http://www.themexp.org/
• http://customize.org/
• http://www.xptheme.info/

• 0 Comments

Here How to Cleaning the Fuser from Hp Laserjet 2400 Printers. Run the printer cleaning page to keep the fuser free of toner and paper particles that can sometimes accumulate. Accumulation of toner and particles can cause specks to appear on the front or back side of your print jobs.

To ensure optimum print quality, HP recommends that you use the cleaning page every time that you replace the print cartridge or on an automatic interval that you can set up. The cleaning procedure takes about 2.5 minutes to complete. A CLEANING message appears on the printer control panel display while the cleaning is taking place.

To run the cleaning page

In order for the cleaning page to work correctly, print the page on copier-grade paper (not bond, heavy, or rough paper).

1. If your printer model includes a duplexer, open the rear output bin.
2. Press MENU to open the menus.
3. Use (UP button) or (DOWN button) to scroll to CONFIGURE DEVICE, and then press (SELECT button).
4. Use (UP button) or (DOWN button) to scroll to PRINT QUALITY, and then press (SELECT button).
5. Use (UP button) or (DOWN button) to scroll to CREATE CLEANING PAGE, and then press (SELECT button).
6. Follow the instructions on the cleaning page to complete the cleaning process.
7. If your printer model includes a duplexer, close the rear output bin.

• 0 Comments

Manual Reset for Canon Pixma MP450 Printers

1. Turn off the Canon Pixma MP450 Printers .
2. Hold button Resume/Cancel (red triangle in the circle), click on POWER - an indicator light green.
3. Release the button Resume / Cancel keeping POWER.
4. Click Resume/Cancel 2 times, keeping POWER, and then release all the buttons.
5. When the indicator recorded GREEN - click Resume / Cancel 4 times!
6. Turn off the Canon Pixma MP450 Printers POWER button.

• 0 Comments