Blog, Adsense, Resetter Printers, Windows

The HP 51641, C1823 & C6578 Cartridges are found in the following printers, Deskjet 700 Series, 800 Series, 900 Series, 1100 Series, 1220 Photo Series, P1000 Photo Series, 710C, 712C, 720C, 722C, 810C, 812C, 820Cse, 820Cxi, 850C, 855C, C1823D, 890C, 895Cxi 1000, 1120C, 1120Cse, 1120 Cxi, Officejet Pro 1150C, 1170C, 1175 HP Officejet All-in-one R40, R60, R80 Color Copier 140, 145, 150

The process below can be used with one cartridge or for resetting both cartridges at the same time. It is recommended that you use this process when needed. Some HP printers do not require ink level resetting.

If you currently use the following HP ink jet cartridges HP 51641, HP 51645, C1823, C6615, C6578 this will allow you to reset the ID system & Ink Level Indicator built into the printer.

To reset the ink monitor to display “Full”, follow this procedure.

• Open printer lid so cartridges move to center of carriage (changing area).
• Lift clamp and remove black or color cartridge from the holder.
• Place a piece of scotch tape over the top left four contacts as shown in the picture.
• Place cartridge back into printer, close lid and wait 10 seconds.
• Open the lid and wait for cartridge to return to “changing area”. The printer may show an error message at this time. This is not uncommon and is nothing to be concerned about.
• Remove cartridge from printer.
• Remove tape from left contact point and place on top right four contact points.
• Place cartridge back into printer, close lid and wait 10 seconds.
• Open the lid and wait for cartridge to return to “changing area”. The printer may show an error message at this time. This is not uncommon and is nothing to be concerned about.
• Remove cartridges from printer then remove tape from cartridges
• Place cartridge back into printer.
• Printer will now recalibrate. Once the process is complete the ink level meter should be reading full again

The Black and Color Ink Cartridge HP 14 (C5011A) is used in the new HP OfficeJet D Series and CP 1160 Ink Jet series.

Reset Ink level the HP C5011A (HP 14) Black and Color cartridge used in the HP OfficeJet D Series.

1. Press the < and > (also the + and -) at the same time, then release quickly (the lcd panel must be showing the date or the procedure will not work)

2. On the keypad, press in order 7, 8, 9 for black cartridge and press in order 4, 5, 6 for color cartridge

3. A message will appear asking if you want to override the ink level gauge. Press 1 for yes (You can later turn the ink gauge back on if you install a new cartridge by going through steps 2 and 3, then pressing 2 when prompted if you want to override the ink level gauge).

4. Your ink level gauge is now turned off and can resume printing.

To turn the ink level gauge off for the HP C5011A (HP 14) black and Color cartridge used in the HP Color InkJet CP 1160 Series :

1. Press and hold down the power button.

2. While holding the Power button:

• Press the Cancel button 12 times

• Press the Resume button 1 time for Black cartridge, Press the Resume button 3 times for color cartridge

1. Release the Power button

The ink gauge is now off and you can resume printing

Service mode is intended for repair technicians and generally the only reason to enter service mode is to change the maintenance count.

HP Laserjet 8000, 8100, and 8150 Series service mode

1. Hold down SELECT and JOB CANCEL while powering on the printer, until all lights are illuminated and the Display is blank. (If the Display Panel reads INTERNAL TEST at this point, the keys were released too soon. Repeat this step until successful.)
2. Press MENU, then SELECT. The message SERVICE MODE is displayed briefly, then the printer automatically begins an INTERNAL TEST. After several seconds, both Control Panel Indicators turn off. (The printer may display WARMING UP if it has not warmed up completely.) After the printer has warmed up and passed the self test, SERVICE MODE is displayed.
3. Press MENU once to display SERVICE MENU.
4. Once it says SERVICE MENU press ITEM to scroll through service mode items.
5. To exit the Service Mode press GO.

HP Laserjet 5si service mode

1. Hold down [Items] and [+] while powering ON the printer, until all lights are illuminated and the Display is blank. (If the Display Panel reads INTERNAL TEST at this point, the keys were released too soon. Repeat this step until successful.)
2. Press [Select]. The message SERVICE MODE is displayed briefly, then the printer automatically begins an INTERNAL TEST. After several seconds, both Control Panel Indicators turn OFF. (The printer may display WARMING UP if it has not warmed up completely.) After the printer has warmed up and passed the self test, SERVICE MODE is displayed.
3. Press [Menus] once to display SERVICE MENU.
4. Once it says SERVICE MENU press ITEM to scroll through service mode items.
5. To exit the Service Mode press [On Line].

Read the rest of this entry »