Reset Methode for Canon Printers i6100, i255, i320, i550, i560, i850, i860, i865, i950, i9100, i9950
Canon i255, i320 Waste Ink Counter Reset
Step 1 : Manual for service mode
- Unplug power and USB.
- Open door and hold power button.
- Connect power.
- Close door, then release power button.
or Step 1: Manual for service mode
- Turn off the printer. And disconnect the printer cable.
- Press and hold the POWER button, turn on the printer.
- The indicator LED should be green.
- Press and release the RESUME button , the indicator LED should be orange.
- Press and release the RESUME button again, the indicator LED should be green.
- Release both buttons.
Step 2 : Software for Permanant
- Reconnect the printer cable.
- Download and Run General Tools software resetter for Canon printers i320, i255 then
- select USB PORT
- Choose SET DESTINATION 1 And it should be reset.
Remark “After service mode Pls use software for permanent reset”
Reset Procedures for Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
- Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
- Hold down Resume button and press Power button.
- Keep holding down Power button and let Resume button go.
- Press Resume button 2 times then let BOTH buttons go.
- Green lights will flash and then stop blinking.
- When green lights are solid, press the Resume button 4 times.
- Press the Power button and the printer should turn off, if not, press the Power button once more.
- Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.
Canon i850, i950, Waste Ink Reset
- Start with the printer OFF
- Hold down RESUME and then hold down POWER
- release RESUME
- press RESUME twice, then release POWER
- Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses – light color – function
| Number of presses | light color | function |
| 0 presses | green | Test print (or exit service mode on i960) |
| 1 press | orange | EEPROM info print (plus grid nozzle diagnostic on i960) |
| 2 presses | green | EEPROM initialize |
| 3 presses | orange | Reset waste ink counter |
Reset Procedures Canon i6100
- Turn off the printer
- Press and hold RESUME button, then press and hold POWER button
- Release the RESUME button
- Next press and release the RESUME button two more times in succession, then release POWER button.
- Press RESUME button for 4 times, this will select the clear waste ink counter function, The lamp will alternate color with each key press.
-
- Service/Factory test printout, including ink sensor check.
- EEPROM - Info printout.
- EEPROM – Initialization.
- Reset the Waste ink counter.
- Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!)
Email Subscription
Stay Updates with this Blog. Get Free email newsletter updates, Enter your Email here:Don't forget to confirm your email subcription
You can leave a response to this article, or trackback from your own site.Incoming search terms for this post:
canon i560 reset, canon i550 reset, reset canon i550, i560 reset, reset canon i560, canon i320 reset, reset canon i850, canon i9100 reset, canon i550 7 orange flashes, i9950 reset
4 Comments to “Reset Methode for Canon Printers i6100, i255, i320, i550, i560, i850, i860, i865, i950, i9100, i9950”
I have tried to reset my Canon i550 but it still flashes 7 orange, when I reset it doesnt flash green,
Great!
I saved 25$ with unblocking my i865.
Thank You.
the printer-head is defect, replace it with new one. I recommend to buy new printer cause the printer-head is too expensive.
Regards
I have a Canon i255 printer and the black ink stopped printing. So i replaced the black ink cartridge and shut the printer opening. However, I cannot obtain any black prints now although the coloured print shows up.Please tell me what is wrong or send me an instruction manual for changing ink cartridges.
Thanks in advance.