Comments on: Troubleshooting Tips for Printer Using Continuous Ink System (CIS)

By: bayu

bayu — Mon, 01 Apr 2013 13:31:33 +0000

Dear All

I have problem, my printer is Epson T13. Problem in Printer is light green after blink if This print ON. so, if i want turn off this print with puss button off this button not work. so i must off cable power.

please help me what i do for repair this printer…

By: Dave

Dave — Sun, 24 Mar 2013 21:48:15 +0000

Just Installed CISS on epson stylus sx430w and printing quality shows lines. How can i achieve better quality?

By: Ishan

Ishan — Tue, 08 Jan 2013 10:49:56 +0000

I was using this ciss for last 4 months & working fine foe Epson t13. But sometimes Even the ink tanks are full of inks the Magenta & Yellow doesn’t print at all…Pls help me with this issue….

By: william

william — Fri, 30 Nov 2012 04:58:48 +0000

good afternoon. I am using Epson stylus T1100. the problem are there are lines to my printouts. if i print in colored the color black is blurred. The cartridge always out of ink. even i perform the ink charging twice after that if I look at the cartridge it has no ink. what will i do..

By: theresa

theresa — Tue, 13 Nov 2012 07:00:21 +0000

bonchi says:
January 12, 2012 at 11:42 am
Hello everyone if it says cartridge should be replaced or can’t be recognized, go to printers and faxes folder.

For epson prnters, right click the printer and choose printing preference, go to maintenance, choose ink cartridge replacement follow instruction until cartridge move the print head to the ink cartridge replacement position.

Since it’s a CISS, no need to replace, lift the cartridge straight up and and push it back again then click next next next until ink cartridge replacement is complete.

Follow these instruction if it says cartridge can’t be recognized or need replacement.

THIS HELPS.. THANKS bonchi

By: vinezmart

vinezmart — Sat, 10 Nov 2012 19:35:04 +0000

i use Epson stylus TX121 continuous ink but two red lights are blinking and the cartridge doesn’t move! and the volume of ink is blank but infact full on actual tank. what should i do?

By: vinezmart

vinezmart — Sat, 10 Nov 2012 19:30:04 +0000

i use Epson stylus TX121 continuous ink but two red lights are blinking and the cartridge doesn’t move! and the volume of ink is blank but infact full on actual tank. what should i do?

By: Ssekanjako Craish

Ssekanjako Craish — Sat, 27 Oct 2012 12:42:14 +0000

Hi i have been using CISS on Hp photo smart C6280 All in one for one month working ok, but now it displays incompatible cartridges. what can i do to get my printer work again
thanks

By: Steve

Steve — Sun, 29 Jul 2012 19:37:34 +0000

Just installed Model No. D-WF600 on an Epson NX110 and all works, except at the end of printing it dumps a lot of black ink on to the low right side of the page just before printing ends. If I use notepad and just print a couple of characters and print the whole page it does not happen. The amount of black ink being ejected onto the page at the end of printing is significant.

Any suggestions on how to stop the black ink from being ejected onto the end of the page?

Thanks

By: Hangker

Hangker — Mon, 23 Jul 2012 01:35:43 +0000

hello…
help me…my printer got problem….i dont know why…when i try pint out using microsoft word, its not working it just print only half page and the its stop(error)…i try print using .pdf file, everything just fine…re-install driver also not working..i hope someone can help me…

By: Gruffalocrumble

Gruffalocrumble — Thu, 28 Jun 2012 13:23:08 +0000

I recently installed the BIGFOOT R1900 CIS from Inkjetfly on my Epson R1900. The installation worked fine, the printer is ready. But I have got exactly the problem, described above:

>>The tubing is getting caught inside the printer resulting in an error message “paper loading error”.<<

I adjusted the length of the tubes a 100 times according to the instructions and tried it again and again. It did not help a bit. What else can I do?

Many thanks!

By: John benedict reyes

John benedict reyes — Wed, 13 Jun 2012 11:46:33 +0000

i have Epson T13

i havent use my printer for a month o 2 month then when i use it and refill the tank the ink get suck back to the tank even i use syringe to suck air on top of the holes in cartride. is it right that i use syringe to suck air on top hole of the cartridge?? and how do i refill the cartridge if i suck air and some ink get suck as well??

even it looks fine no more air bubble in the hose but some color might not print at all if i do suck and cleaning several times it will print then gone again why it always some color not printing. how do i clean it example with little water to effective clean it.

Hope u might help me regarding this matter.

By: yz

yz — Wed, 13 Jun 2012 02:19:23 +0000

i need service manual for canon mp145, could you help me please

By: Nheff

Nheff — Tue, 15 May 2012 01:00:41 +0000

Hi,

We have a CISS EPSON Stylus Office T1100, the cyan color is not working properly, green pictures or color are not printing properly, what step I can do to repair the cyan?

thanks,
nheff

By: Mark

Mark — Mon, 30 Apr 2012 02:22:59 +0000

My HP deskjet F2100 was using continnous ink system but the hose of magenta,cyan,black are not going through the cartridge.